Search Criteria
Products meeting the search criteria
Model: A4988
A4988 Stepper Motor Driver
Description:
The A4988 driver is a commonly used bipolar stepper motor driver that can provide up to 2A current per coil from 8V to 35V. These drivers are used to drive NEMA 17 motors on the Mill One. This driver also allows for up to 16th microstepping.
Each pack..
$ 7.05
Ex Tax:$ 7.05
Model: DRV8825
DRV8825 Stepper Motor Driver
Description:
This is a break out board for DRV8825 microstepping bipolar stepper motor drive. It can drive a bipolar stepper motor with an output current of up to up to 2.5 A per coil. It is suitable for driving motors at wide range of voltages from 8.2 V to 45 V.
..
$ 9.87
Ex Tax:$ 9.87
Model: 5V 4-Phase
Stepper Motor 5V 4-Phase 5-Wire & ULN2003 Driver Board
Description:
This is 28YBJ-48 DC 5V 4 phase 5 wire stepper motor with ULN2003 driver board
5-wire phase can drive ordinary uln2003 chip can also be connected as phase 2 may be supporting the development board, direct plug, easy to use..
$ 16.92
Ex Tax:$ 16.92
Model: 17HS
Technical specifications:
* Step: 1.8 degrees;
* Current: 1.7 A;
* Rated voltage: 3.4 V
* Phase resistance: 3 ohm
* Holding torque: 0.35 Nm;
* Inductance: 2.5 mH;
* Dimensions:
* Body: 42 x 40 mm;
* Length: 34 mm;
* Shaft diameter 5 mm;
* Shaft length: 21 mm;
* Weight: 350 g;
..
$ 22.56
Ex Tax:$ 22.56
Model: L298N H
L298N Module Dual H Bridge Stepper Motor Driver Board Modules
Specification:
Driver chip: L298N dual H-bridge driver chip
Terminal driver part of the supply area VMS: +5 V ~ +35 V
Drive part of the peak current Io: 2A / Bridge
Logical part of the terminal power supply range Vss :4.5-5..
$ 7.05
Ex Tax:$ 7.05
Model: MD556
Features
Patented technology
Pure-sinusoidal precise current control technology
Extreme low motor noise
Both driver and motor low heating
High performance, low cost
Supply voltage up to +50VDC, peak current to 5.6A
Optically isolated differential input signals
Pulse frequency up to 400 KHz..
$ 63.45
Ex Tax:$ 63.45
Model: A3987
Description: The EasyDriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse (or 0 to 3.3V pulse if you solder SJ2 closed on the EasyDriver). EasyDriver requires a 7V to 20V supply to power the motor and can power any voltage of stepper motor...
$ 11.99
Ex Tax:$ 11.99
Model: M415
Features:
1. Working power supply 9 V ~ 42 V .
2. Maximum drive current 4 A .
3. the input signal is high-speed optical insulation .
4. provide semi-automatic current locking function .
5. built-in thermal protection and overcurrent protection .
6. Designed in a small size and convenien..
$ 49.35
Ex Tax:$ 49.35
Model: TB6560
The TB6560 Driver Board 3A CNC Router Single 1 Axis Controller Stepper Motor driver board is for axis control with Input signal high-speed optocoupler isolation, the large heat sink to ensure good heat dissipation. Stepper motor driver is Semi-flow mode adjustable, semi-flow..
$ 28.20
Ex Tax:$ 28.20
Model: SMEB-A4988-DRV8825
Description
A4988 / DRV8825 Stepper Motor Driver Expansion Board for 3D Printer Parts is use to extend the A4988 or DRV8825 stepper motor driver module.
You can use A4988 / DRV8825, take care of the direction when inserting, or it may burn down the driver.
The jumper hits the position of ON DP to..
$ 8.46
Ex Tax:$ 8.46
Showing 1 to 10 of 10 (1 Pages)
